| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: xhci: bail out of setup if the controller is inaccessible
xhci_gen_setup() locates the operational registers using the capability
length read from the very first register:
xhci->op_regs = hcd->regs +
HC_LENGTH(readl(&xhci->cap_regs->hc_capbase));
If the controller is dead or has dropped off the bus, that read returns
~0, HC_LENGTH() truncates it to 0xff, and op_regs ends up 0xff bytes
past the page-aligned MMIO base, i.e. unaligned. The first access
through it, xhci_halt() -> xhci_handshake() reading op_regs->status, is
then an unaligned readl() on device memory. arm64 faults on unaligned
device accesses, so instead of xhci_handshake() catching the all-ones
value and returning -ENODEV, setup oopses:
xhci-pci-renesas 0005:08:00.0: Unable to change power state from D3cold to D0, device inaccessible
xhci-pci-renesas 0005:08:00.0: xHCI Host Controller
xhci-pci-renesas 0005:08:00.0: new USB bus registered, assigned bus number 1
Unable to handle kernel paging request at virtual address ffff80030a770103
ESR = 0x0000000096000021
FSC = 0x21: alignment fault
Internal error: Oops: 0000000096000021 [#1] SMP
pc : xhci_halt [xhci_hcd]
Call trace:
xhci_halt
xhci_gen_setup
xhci_pci_setup
usb_add_hcd
usb_hcd_pci_probe
xhci_pci_common_probe
xhci_pci_renesas_probe
This was hit with a Renesas uPD720201 that failed to power up ("Unable
to change power state from D3cold to D0, device inaccessible") yet still
reached the HCD probe path.
Read the capability register once, and if it reads back the all-ones
value (as xhci_handshake() and xhci_reset() already test for), abort
setup with -ENODEV before op_regs is derived from it. Reading it once
also avoids re-reading a register that may change under a concurrent
hot-removal. |
| In the Linux kernel, the following vulnerability has been resolved:
fuse: fix invalidate lock leak on open O_TRUNC DAX failure
fuse_open() takes filemap_invalidate_lock() for a DAX truncate
(dax_truncate = true) and releases it before the out_inode_unlock
label. But when fuse_dax_break_layouts() fails, the goto
out_inode_unlock skips the unlock and leaks the rwsem, so any later
fault or truncate on the file stalls on the stale lock.
fuse_dax_break_layouts() can fail with -ERESTARTSYS when a signal
interrupts the wait for busy DAX pages to drain:
open("file", O_RDWR | O_TRUNC)
└─ fuse_open()
├─ filemap_invalidate_lock() # dax_truncate
└─ fuse_dax_break_layouts()
└─ dax_break_layout()
└─ wait_page_idle() # TASK_INTERRUPTIBLE
└─ fuse_wait_dax_page() # unlock, schedule, re-lock
└─ signal → -ERESTARTSYS
goto out_inode_unlock # <- lock leaked
Fix this by moving filemap_invalidate_unlock() below the label so
that all error paths release the lock, and rename the label to
out_unlock as it now covers more than just the inode lock. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: Wrap user-invoked calls to fb_set_var() in helper
Handle fbcon during display updates in fb_set_var_from_user(). Check
with fbcon if the mode change is possible, update hardware state and
finally update fbcon. Update all callers.
Only the FBIOPUT_VSCREENINFO ioctl currently does all steps. Other
mode-changes callers in sysfs and driver code are missing fbcon-related
steps.
With the new helper, ps3fb and sh_mobile_lcdcfb no longer maintain
fbcon state themselves. |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: Avoid calling WARN_ON() on -ENOMEM in cfg802154_switch_netns()
It's pointless to call WARN_ON() in case of an allocation failure in
dev_change_net_namespace() and device_rename(), since it only leads to
useless splats caused by deliberate fault injections, so avoid it.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject sleepable BPF_LSM_CGROUP programs at load time
The cgroup shim runs under rcu_read_lock_dont_migrate(), so we should
not attach any sleepable BPF programs there. Add support to the verifier
to explicitly reject attempts to load sleepable BPF programs destined
for LSM cgroup attachment.
Without this, we get the following splat from a BPF_LSM_CGROUP
program marked BPF_F_SLEEPABLE attached to file_open when it calls
bpf_get_dentry_xattr():
BUG: sleeping function called from invalid context at kernel/locking/rwsem.c:1567
in_atomic(): 0, irqs_disabled(): 0, non_block: 0, pid: 34317, name: load
preempt_count: 0, expected: 0
RCU nest depth: 2, expected: 0
Call Trace:
down_read+0x76/0x480
ext4_xattr_get+0x11f/0x700
__vfs_getxattr+0xf0/0x150
bpf_get_dentry_xattr+0xbb/0xf0
bpf_prog_e76a298dac9218c6_test_open+0x6a/0x85
__cgroup_bpf_run_lsm_current+0x326/0x840
bpf_trampoline_6442534646+0x62/0x14d
security_file_open+0x34/0x60
do_dentry_open+0x340/0x1260
vfs_open+0x7a/0x440
path_openat+0x1bac/0x30a0
libbpf provides a .s named section variant for every sleepable
program type except lsm_cgroup, reflecting that per-cgroup LSM programs
are intended to only run in a non-sleepable context.
The above splat was obtained by bypassing libbpf by using bpf(2)
directly. |
| In the Linux kernel, the following vulnerability has been resolved:
ata: sata_dwc_460ex: fix infinite loop in NCQ tag completion bit-scanning
The hand-rolled bit-scanning loop in the NCQ completion path has an
infinite loop bug. When tag_mask has only high bits set (e.g.
0x80000000), the inner while loop left-shifts tag_mask until it
overflows to 0. At that point !(0 & 1) is always true and 0 <<= 1
stays 0, causing an infinite loop in hardirq context with a spinlock
held.
Replace the open-coded bit-scanning with __ffs() which correctly
finds the least significant set bit and is bounded by the width of
the argument. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: use wiphy work for socket owner autodisconnect
nl80211_netlink_notify() walks the cfg80211 wireless device list when a
NETLINK_GENERIC socket is released. If the socket owns a connection, the
notifier queues the embedded wdev->disconnect_wk work item.
That work is a plain work_struct today. NETDEV_GOING_DOWN cancels it, but a
NETLINK_URELEASE notifier that already observed conn_owner_nlportid can
queue it after that cancel returns. _cfg80211_unregister_wdev() then
removes the wdev from the list and waits for RCU readers, but
synchronize_net() does not drain work queued by such a reader.
Make the autodisconnect work a wiphy_work instead. The callback already
needs the wiphy mutex, and wiphy_work runs under that mutex. This lets
teardown cancel pending autodisconnect work while holding the mutex,
without a cancel_work_sync() vs. worker locking concern.
Also cancel the wiphy work after list_del_rcu() and synchronize_net(). Any
NETLINK_URELEASE notifier that had already reached the wdev list has then
either queued the work and it is removed, or can no longer find the wdev. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: Move jump_label_init() before parse_early_param()
When enabling both CONFIG_MEM_ALLOC_PROFILING=y and
CONFIG_MEM_ALLOC_PROFILING_ENABLED_BY_DEFAULT=y, then diabling memory
profiling by adding the boot parameter 'sysctl.vm.mem_profiling=0' will
cause the kernel failed to boot.
After analysis, this is because jump_label_init() must be called before
parse_early_param(), the early param handlers may modify static keys by
static_branch_enable/disable().
Fix this by moving jump_label_init() to before parse_early_param(). The
solution is similar to other architectures. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/core: Detach event groups during remove_on_exec
perf_event_remove_on_exec() removes events by calling
perf_event_exit_event(). For top-level events, this removes the event from
the context with DETACH_EXIT only.
This can leave inconsistent group state when a removed event is a group
leader and the group contains siblings without remove_on_exec. If the group
was active, the surviving siblings can remain active and attached to the
removed leader's sibling list, but are no longer represented by a valid
group leader on the PMU context active lists.
A later close of the removed leader uses DETACH_GROUP and can promote the
still-active siblings from this stale group state. The next schedule-in can
then add an already-linked active_list entry again, corrupting the PMU
context active list.
With DEBUG_LIST enabled, this is caught as a list_add double-add in
merge_sched_in().
Fix this by detaching group relationships when remove_on_exec removes an
event. This preserves the existing task-exit and revoke behavior, while
ensuring surviving siblings are ungrouped before the removed event leaves
the context. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix deadlock between reflink and transaction commit when using flushoncommit
When using the flushoncommit mount option, we can have a deadlock between
a transaction commit and a reflink operation that copied an inline extent
to an offset beyond the current i_size of the destination node.
The deadlock happens like this:
1) Task A clones an inline extent from inode X to an offset of inode Y
that is beyond Y's current i_size. This means we copied the inline
extent's data to a folio of inode Y that is beyond its EOF, using a
call to copy_inline_to_page();
2) Task B starts a transaction commit and calls
btrfs_start_delalloc_flush() to flush delalloc;
3) The delalloc flushing sees the new dirty folio of inode Y and when it
attempts to flush it, it ends up at extent_writepage() and sees that
the offset of the folio is beyond the i_size of inode Y, so it attempts
to invalidate the folio by calling folio_invalidate(), which ends up at
btrfs' folio invalidate callback - btrfs_invalidate_folio(). There it
tries to lock the folio's range in inode Y's extent io tree, but it
blocks since it's currently locked by task A - during a reflink we lock
the inodes and the source and destination ranges after flushing all
delalloc and waiting for ordered extent completion - after that we
don't expect to have dirty folios in the ranges, the exception is if
we have to copy an inline extent's data (because the destination offset
is not zero);
4) Task A then attempts to start a transaction to update the inode item,
and then it's blocked since the current transaction is in the
TRANS_STATE_COMMIT_START state. Therefore task A has to wait for the
current transaction to become unblocked (its state >=
TRANS_STATE_UNBLOCKED).
So task A is waiting for the transaction commit done by task B, and
the later waiting on the extent lock of inode Y that is currently
held by task A.
Syzbot recently reported this with the following stack traces:
INFO: task kworker/u8:7:1053 blocked for more than 143 seconds.
Not tainted syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u8:7 state:D stack:23520 pid:1053 tgid:1053 ppid:2 task_flags:0x4208060 flags:0x00080000
Workqueue: writeback wb_workfn (flush-btrfs-46)
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5298 [inline]
__schedule+0x1553/0x5240 kernel/sched/core.c:6911
__schedule_loop kernel/sched/core.c:6993 [inline]
schedule+0x164/0x360 kernel/sched/core.c:7008
wait_extent_bit fs/btrfs/extent-io-tree.c:811 [inline]
btrfs_lock_extent_bits+0x59c/0x700 fs/btrfs/extent-io-tree.c:1914
btrfs_lock_extent fs/btrfs/extent-io-tree.h:152 [inline]
btrfs_invalidate_folio+0x43d/0xc40 fs/btrfs/inode.c:7704
extent_writepage fs/btrfs/extent_io.c:1852 [inline]
extent_write_cache_pages fs/btrfs/extent_io.c:2580 [inline]
btrfs_writepages+0x12ff/0x2440 fs/btrfs/extent_io.c:2713
do_writepages+0x32e/0x550 mm/page-writeback.c:2554
__writeback_single_inode+0x133/0x11a0 fs/fs-writeback.c:1750
writeback_sb_inodes+0x995/0x19d0 fs/fs-writeback.c:2042
wb_writeback+0x456/0xb70 fs/fs-writeback.c:2227
wb_do_writeback fs/fs-writeback.c:2374 [inline]
wb_workfn+0x41a/0xf60 fs/fs-writeback.c:2414
process_one_work kernel/workqueue.c:3276 [inline]
process_scheduled_works+0xb6e/0x18c0 kernel/workqueue.c:3359
worker_thread+0xa53/0xfc0 kernel/workqueue.c:3440
kthread+0x388/0x470 kernel/kthread.c:436
ret_from_fork+0x51e/0xb90 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
INFO: task syz.4.64:6910 blocked for more than 143 seconds.
Not tainted syzkaller #0
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:syz.4.64 state:D stack:22752 pid:6910 tgid:
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: move wait_on_sem() out of spinlock
With iommu.strict=1, the existing completion wait path can cause soft
lockups under stressed environment, as wait_on_sem() busy-waits under the
spinlock with interrupts disabled.
Move the completion wait in iommu_completion_wait() out of the spinlock.
wait_on_sem() only polls the hardware-updated cmd_sem and does not require
iommu->lock, so holding the lock during the busy wait unnecessarily
increases contention and extends the time with interrupts disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: Fix locking usage for tcon fields
We used to use the cifs_tcp_ses_lock to protect a lot of objects
that are not just the server, ses or tcon lists. We later introduced
srv_lock, ses_lock and tc_lock to protect fields within the
corresponding structs. This was done to provide a more granular
protection and avoid unnecessary serialization.
There were still a couple of uses of cifs_tcp_ses_lock to provide
tcon fields. In this patch, I've replaced them with tc_lock. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: move async event work off nvmet-wq
For target nvmet_ctrl_free() flushes ctrl->async_event_work.
If nvmet_ctrl_free() runs on nvmet-wq, the flush re-enters workqueue
completion for the same worker:-
A. Async event work queued on nvmet-wq (prior to disconnect):
nvmet_execute_async_event()
queue_work(nvmet_wq, &ctrl->async_event_work)
nvmet_add_async_event()
queue_work(nvmet_wq, &ctrl->async_event_work)
B. Full pre-work chain (RDMA CM path):
nvmet_rdma_cm_handler()
nvmet_rdma_queue_disconnect()
__nvmet_rdma_queue_disconnect()
queue_work(nvmet_wq, &queue->release_work)
process_one_work()
lock((wq_completion)nvmet-wq) <--------- 1st
nvmet_rdma_release_queue_work()
C. Recursive path (same worker):
nvmet_rdma_release_queue_work()
nvmet_rdma_free_queue()
nvmet_sq_destroy()
nvmet_ctrl_put()
nvmet_ctrl_free()
flush_work(&ctrl->async_event_work)
__flush_work()
touch_wq_lockdep_map()
lock((wq_completion)nvmet-wq) <--------- 2nd
Lockdep splat:
============================================
WARNING: possible recursive locking detected
6.19.0-rc3nvme+ #14 Tainted: G N
--------------------------------------------
kworker/u192:42/44933 is trying to acquire lock:
ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: touch_wq_lockdep_map+0x26/0x90
but task is already holding lock:
ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x53e/0x660
3 locks held by kworker/u192:42/44933:
#0: ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x53e/0x660
#1: ffffc9000e6cbe28 ((work_completion)(&queue->release_work)){+.+.}-{0:0}, at: process_one_work+0x1c5/0x660
#2: ffffffff82d4db60 (rcu_read_lock){....}-{1:3}, at: __flush_work+0x62/0x530
Workqueue: nvmet-wq nvmet_rdma_release_queue_work [nvmet_rdma]
Call Trace:
__flush_work+0x268/0x530
nvmet_ctrl_free+0x140/0x310 [nvmet]
nvmet_cq_put+0x74/0x90 [nvmet]
nvmet_rdma_free_queue+0x23/0xe0 [nvmet_rdma]
nvmet_rdma_release_queue_work+0x19/0x50 [nvmet_rdma]
process_one_work+0x206/0x660
worker_thread+0x184/0x320
kthread+0x10c/0x240
ret_from_fork+0x319/0x390
Move async event work to a dedicated nvmet-aen-wq to avoid reentrant
flush on nvmet-wq. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/core) Protect regulator operations with mutex
The regulator operations pmbus_regulator_get_voltage(),
pmbus_regulator_set_voltage(), and pmbus_regulator_list_voltage()
access PMBus registers and shared data but were not protected by
the update_lock mutex. This could lead to race conditions.
However, adding mutex protection directly to these functions causes
a deadlock because pmbus_regulator_notify() (which calls
regulator_notifier_call_chain()) is often called with the mutex
already held (e.g., from pmbus_fault_handler()). If a regulator
callback then calls one of the now-protected voltage functions,
it will attempt to acquire the same mutex.
Rework pmbus_regulator_notify() to utilize a worker function to
send notifications outside of the mutex protection. Events are
stored as atomics in a per-page bitmask and processed by the worker.
Initialize the worker and its associated data during regulator
registration, and ensure it is cancelled on device removal using
devm_add_action_or_reset().
While at it, remove the unnecessary include of linux/of.h. |
| In the Linux kernel, the following vulnerability has been resolved:
net/rds: Fix circular locking dependency in rds_tcp_tune
syzbot reported a circular locking dependency in rds_tcp_tune() where
sk_net_refcnt_upgrade() is called while holding the socket lock:
======================================================
WARNING: possible circular locking dependency detected
======================================================
kworker/u10:8/15040 is trying to acquire lock:
ffffffff8e9aaf80 (fs_reclaim){+.+.}-{0:0},
at: __kmalloc_cache_noprof+0x4b/0x6f0
but task is already holding lock:
ffff88805a3c1ce0 (k-sk_lock-AF_INET6){+.+.}-{0:0},
at: rds_tcp_tune+0xd7/0x930
The issue occurs because sk_net_refcnt_upgrade() performs memory
allocation (via get_net_track() -> ref_tracker_alloc()) while the
socket lock is held, creating a circular dependency with fs_reclaim.
Fix this by moving sk_net_refcnt_upgrade() outside the socket lock
critical section. This is safe because the fields modified by the
sk_net_refcnt_upgrade() call (sk_net_refcnt, ns_tracker) are not
accessed by any concurrent code path at this point.
v2:
- Corrected fixes tag
- check patch line wrap nits
- ai commentary nits |
| In the Linux kernel, the following vulnerability has been resolved:
pNFS: Fix a deadlock when returning a delegation during open()
Ben Coddington reports seeing a hang in the following stack trace:
0 [ffffd0b50e1774e0] __schedule at ffffffff9ca05415
1 [ffffd0b50e177548] schedule at ffffffff9ca05717
2 [ffffd0b50e177558] bit_wait at ffffffff9ca061e1
3 [ffffd0b50e177568] __wait_on_bit at ffffffff9ca05cfb
4 [ffffd0b50e1775c8] out_of_line_wait_on_bit at ffffffff9ca05ea5
5 [ffffd0b50e177618] pnfs_roc at ffffffffc154207b [nfsv4]
6 [ffffd0b50e1776b8] _nfs4_proc_delegreturn at ffffffffc1506586 [nfsv4]
7 [ffffd0b50e177788] nfs4_proc_delegreturn at ffffffffc1507480 [nfsv4]
8 [ffffd0b50e1777f8] nfs_do_return_delegation at ffffffffc1523e41 [nfsv4]
9 [ffffd0b50e177838] nfs_inode_set_delegation at ffffffffc1524a75 [nfsv4]
10 [ffffd0b50e177888] nfs4_process_delegation at ffffffffc14f41dd [nfsv4]
11 [ffffd0b50e1778a0] _nfs4_opendata_to_nfs4_state at ffffffffc1503edf [nfsv4]
12 [ffffd0b50e1778c0] _nfs4_open_and_get_state at ffffffffc1504e56 [nfsv4]
13 [ffffd0b50e177978] _nfs4_do_open at ffffffffc15051b8 [nfsv4]
14 [ffffd0b50e1779f8] nfs4_do_open at ffffffffc150559c [nfsv4]
15 [ffffd0b50e177a80] nfs4_atomic_open at ffffffffc15057fb [nfsv4]
16 [ffffd0b50e177ad0] nfs4_file_open at ffffffffc15219be [nfsv4]
17 [ffffd0b50e177b78] do_dentry_open at ffffffff9c09e6ea
18 [ffffd0b50e177ba8] vfs_open at ffffffff9c0a082e
19 [ffffd0b50e177bd0] dentry_open at ffffffff9c0a0935
The issue is that the delegreturn is being asked to wait for a layout
return that cannot complete because a state recovery was initiated. The
state recovery cannot complete until the open() finishes processing the
delegations it was given.
The solution is to propagate the existing flags that indicate a
non-blocking call to the function pnfs_roc(), so that it knows not to
wait in this situation. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/vmalloc, mm/kasan: respect gfp mask in kasan_populate_vmalloc()
kasan_populate_vmalloc() and its helpers ignore the caller's gfp_mask and
always allocate memory using the hardcoded GFP_KERNEL flag. This makes
them inconsistent with vmalloc(), which was recently extended to support
GFP_NOFS and GFP_NOIO allocations.
Page table allocations performed during shadow population also ignore the
external gfp_mask. To preserve the intended semantics of GFP_NOFS and
GFP_NOIO, wrap the apply_to_page_range() calls into the appropriate
memalloc scope.
xfs calls vmalloc with GFP_NOFS, so this bug could lead to deadlock.
There was a report here
https://lkml.kernel.org/r/686ea951.050a0220.385921.0016.GAE@google.com
This patch:
- Extends kasan_populate_vmalloc() and helpers to take gfp_mask;
- Passes gfp_mask down to alloc_pages_bulk() and __get_free_page();
- Enforces GFP_NOFS/NOIO semantics with memalloc_*_save()/restore()
around apply_to_page_range();
- Updates vmalloc.c and percpu allocator call sites accordingly. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: Optimize module load time by optimizing PLT/GOT counting
When enabling CONFIG_KASAN, CONFIG_PREEMPT_VOLUNTARY_BUILD and
CONFIG_PREEMPT_VOLUNTARY at the same time, there will be soft deadlock,
the relevant logs are as follows:
rcu: INFO: rcu_sched self-detected stall on CPU
...
Call Trace:
[<900000000024f9e4>] show_stack+0x5c/0x180
[<90000000002482f4>] dump_stack_lvl+0x94/0xbc
[<9000000000224544>] rcu_dump_cpu_stacks+0x1fc/0x280
[<900000000037ac80>] rcu_sched_clock_irq+0x720/0xf88
[<9000000000396c34>] update_process_times+0xb4/0x150
[<90000000003b2474>] tick_nohz_handler+0xf4/0x250
[<9000000000397e28>] __hrtimer_run_queues+0x1d0/0x428
[<9000000000399b2c>] hrtimer_interrupt+0x214/0x538
[<9000000000253634>] constant_timer_interrupt+0x64/0x80
[<9000000000349938>] __handle_irq_event_percpu+0x78/0x1a0
[<9000000000349a78>] handle_irq_event_percpu+0x18/0x88
[<9000000000354c00>] handle_percpu_irq+0x90/0xf0
[<9000000000348c74>] handle_irq_desc+0x94/0xb8
[<9000000001012b28>] handle_cpu_irq+0x68/0xa0
[<9000000001def8c0>] handle_loongarch_irq+0x30/0x48
[<9000000001def958>] do_vint+0x80/0xd0
[<9000000000268a0c>] kasan_mem_to_shadow.part.0+0x2c/0x2a0
[<90000000006344f4>] __asan_load8+0x4c/0x120
[<900000000025c0d0>] module_frob_arch_sections+0x5c8/0x6b8
[<90000000003895f0>] load_module+0x9e0/0x2958
[<900000000038b770>] __do_sys_init_module+0x208/0x2d0
[<9000000001df0c34>] do_syscall+0x94/0x190
[<900000000024d6fc>] handle_syscall+0xbc/0x158
After analysis, this is because the slow speed of loading the amdgpu
module leads to the long time occupation of the cpu and then the soft
deadlock.
When loading a module, module_frob_arch_sections() tries to figure out
the number of PLTs/GOTs that will be needed to handle all the RELAs. It
will call the count_max_entries() to find in an out-of-order date which
counting algorithm has O(n^2) complexity.
To make it faster, we sort the relocation list by info and addend. That
way, to check for a duplicate relocation, it just needs to compare with
the previous entry. This reduces the complexity of the algorithm to O(n
log n), as done in commit d4e0340919fb ("arm64/module: Optimize module
load time by optimizing PLT counting"). This gives sinificant reduction
in module load time for modules with large number of relocations.
After applying this patch, the soft deadlock problem has been solved,
and the kernel starts normally without "Call Trace".
Using the default configuration to test some modules, the results are as
follows:
Module Size
ip_tables 36K
fat 143K
radeon 2.5MB
amdgpu 16MB
Without this patch:
Module Module load time (ms) Count(PLTs/GOTs)
ip_tables 18 59/6
fat 0 162/14
radeon 54 1221/84
amdgpu 1411 4525/1098
With this patch:
Module Module load time (ms) Count(PLTs/GOTs)
ip_tables 18 59/6
fat 0 162/14
radeon 22 1221/84
amdgpu 45 4525/1098 |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix potential deadloop in prepare_compress_overwrite()
Jan Prusakowski reported a kernel hang issue as below:
When running xfstests on linux-next kernel (6.14.0-rc3, 6.12) I
encountered a problem in generic/475 test where fsstress process
gets blocked in __f2fs_write_data_pages() and the test hangs.
The options I used are:
MKFS_OPTIONS -- -O compression -O extra_attr -O project_quota -O quota /dev/vdc
MOUNT_OPTIONS -- -o acl,user_xattr -o discard,compress_extension=* /dev/vdc /vdc
INFO: task kworker/u8:0:11 blocked for more than 122 seconds.
Not tainted 6.14.0-rc3-xfstests-lockdep #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:kworker/u8:0 state:D stack:0 pid:11 tgid:11 ppid:2 task_flags:0x4208160 flags:0x00004000
Workqueue: writeback wb_workfn (flush-253:0)
Call Trace:
<TASK>
__schedule+0x309/0x8e0
schedule+0x3a/0x100
schedule_preempt_disabled+0x15/0x30
__mutex_lock+0x59a/0xdb0
__f2fs_write_data_pages+0x3ac/0x400
do_writepages+0xe8/0x290
__writeback_single_inode+0x5c/0x360
writeback_sb_inodes+0x22f/0x570
wb_writeback+0xb0/0x410
wb_do_writeback+0x47/0x2f0
wb_workfn+0x5a/0x1c0
process_one_work+0x223/0x5b0
worker_thread+0x1d5/0x3c0
kthread+0xfd/0x230
ret_from_fork+0x31/0x50
ret_from_fork_asm+0x1a/0x30
</TASK>
The root cause is: once generic/475 starts toload error table to dm
device, f2fs_prepare_compress_overwrite() will loop reading compressed
cluster pages due to IO error, meanwhile it has held .writepages lock,
it can block all other writeback tasks.
Let's fix this issue w/ below changes:
- add f2fs_handle_page_eio() in prepare_compress_overwrite() to
detect IO error.
- detect cp_error earler in f2fs_read_multi_pages(). |
| In the Linux kernel, the following vulnerability has been resolved:
eth: bnxt: fix truesize for mb-xdp-pass case
When mb-xdp is set and return is XDP_PASS, packet is converted from
xdp_buff to sk_buff with xdp_update_skb_shared_info() in
bnxt_xdp_build_skb().
bnxt_xdp_build_skb() passes incorrect truesize argument to
xdp_update_skb_shared_info().
The truesize is calculated as BNXT_RX_PAGE_SIZE * sinfo->nr_frags but
the skb_shared_info was wiped by napi_build_skb() before.
So it stores sinfo->nr_frags before bnxt_xdp_build_skb() and use it
instead of getting skb_shared_info from xdp_get_shared_info_from_buff().
Splat looks like:
------------[ cut here ]------------
WARNING: CPU: 2 PID: 0 at net/core/skbuff.c:6072 skb_try_coalesce+0x504/0x590
Modules linked in: xt_nat xt_tcpudp veth af_packet xt_conntrack nft_chain_nat xt_MASQUERADE nf_conntrack_netlink xfrm_user xt_addrtype nft_coms
CPU: 2 UID: 0 PID: 0 Comm: swapper/2 Not tainted 6.14.0-rc2+ #3
RIP: 0010:skb_try_coalesce+0x504/0x590
Code: 4b fd ff ff 49 8b 34 24 40 80 e6 40 0f 84 3d fd ff ff 49 8b 74 24 48 40 f6 c6 01 0f 84 2e fd ff ff 48 8d 4e ff e9 25 fd ff ff <0f> 0b e99
RSP: 0018:ffffb62c4120caa8 EFLAGS: 00010287
RAX: 0000000000000003 RBX: ffffb62c4120cb14 RCX: 0000000000000ec0
RDX: 0000000000001000 RSI: ffffa06e5d7dc000 RDI: 0000000000000003
RBP: ffffa06e5d7ddec0 R08: ffffa06e6120a800 R09: ffffa06e7a119900
R10: 0000000000002310 R11: ffffa06e5d7dcec0 R12: ffffe4360575f740
R13: ffffe43600000000 R14: 0000000000000002 R15: 0000000000000002
FS: 0000000000000000(0000) GS:ffffa0755f700000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f147b76b0f8 CR3: 00000001615d4000 CR4: 00000000007506f0
PKRU: 55555554
Call Trace:
<IRQ>
? __warn+0x84/0x130
? skb_try_coalesce+0x504/0x590
? report_bug+0x18a/0x1a0
? handle_bug+0x53/0x90
? exc_invalid_op+0x14/0x70
? asm_exc_invalid_op+0x16/0x20
? skb_try_coalesce+0x504/0x590
inet_frag_reasm_finish+0x11f/0x2e0
ip_defrag+0x37a/0x900
ip_local_deliver+0x51/0x120
ip_sublist_rcv_finish+0x64/0x70
ip_sublist_rcv+0x179/0x210
ip_list_rcv+0xf9/0x130
How to reproduce:
<Node A>
ip link set $interface1 xdp obj xdp_pass.o
ip link set $interface1 mtu 9000 up
ip a a 10.0.0.1/24 dev $interface1
<Node B>
ip link set $interfac2 mtu 9000 up
ip a a 10.0.0.2/24 dev $interface2
ping 10.0.0.1 -s 65000
Following ping.py patch adds xdp-mb-pass case. so ping.py is going to be
able to reproduce this issue. |
