| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In Reactor Core, applications that use the Flux.bufferTimeout operator with fairBackpressure enabled are vulnerable to a Denial of Service (DoS) condition.
Reactor Core 3.8.0 - 3.8.6
Reactor Core 3.7.19 and earlier |
| A flaw was found in libssh. A remote authenticated peer can advertise a zero maximum packet size in SSH_MSG_CHANNEL_OPEN, causing later channel writes to loop indefinitely and consume CPU, leading to denial of service. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wlcore: enable the right set of ciphers
The firmware version number check for IGTK introduced in
commit c34dbc5900b0 ("wifi: wlcore: Add support for IGTK key")
lets the amount of ciphers decrease on every boot of a too old firmware and
that is practically happening. It also does not take into account other
chips than the wl18xx. On some wl128x, the following can be observed
when connecting via nm to a common ap:
[ 484.113311] wlcore: WARNING could not set keys
[ 484.117828] wlcore: ERROR Could not add or replace key
[ 484.123016] wlan0: failed to set key (5, ff:ff:ff:ff:ff:ff) to hardware (-5)
[ 484.123046] wlcore: Hardware recovery in progress. FW ver: Rev 7.3.10.0.142
[ 484.139923] wlcore: pc: 0x0, hint_sts: 0x00000048 count: 1
[ 484.145721] wlcore: down
[ 484.148986] ieee80211 phy0: Hardware restart was requested
[ 484.610473] wlcore: firmware booted (Rev 7.3.10.0.142)
[ 484.633758] wlcore: Association completed.
[ 484.690490] wlcore: ERROR command execute failure 14
[ 484.690490] ------------[ cut here ]------------
[ 484.700195] WARNING: drivers/net/wireless/ti/wlcore/main.c:872 at wl12xx_queue_recovery_work+0x64/0x74 [wlcore], CPU#0: kworker/0:0/892
This repeats endlessly.
Always disable IGTK on wl12xx and fix the decrementing mess. |
| An unauthenticated attacker can send a truncated quoted argument to the ManageSieve login process, which makes it spin in an infinite loop consuming CPU. This can cause degradation or denial of service for Sieve script management, and repeated connections can consume all available CPU on the server. Monitor system for abnormal CPU usage and kill the offending process. Restrict network access to the ManageSieve service to trusted clients. Update to non-vulnerable version. No publicly available exploits are known. |
| A vulnerability has been found in BareBones BBEdit up to 15.5.5. The affected element is an unknown function of the component Lasso Language Tokenizer. Such manipulation leads to infinite loop. The attack can be executed remotely. Upgrading to version 16.0 is sufficient to fix this issue. The affected component should be upgraded. |
| Loop with Unreachable Exit Condition (Infinite Loop) vulnerability in ash-project ash_ai allows an attacker who can influence a model's output to hang the tool loop and drive unbounded, repeated model requests.
AshAi.ToolLoop classifies a model response of :tool_calls, then filters the calls through normalize_tool_calls/2 and unprocessed_tool_calls/2. Both can empty the list: a call missing a valid name, or one reusing a tool_call_id that already has a result in history, is dropped. With an empty list the loop appended nothing and recursed with a byte-identical message list, so the conversation never advanced and the same request was re-sent every iteration. Under the supported max_iterations: :infinity this never terminated; otherwise it exhausted the full budget. Prompt-injected content can make the model re-emit a spent tool_call_id. The fix treats an empty post-filter list as terminal.
This issue affects ash_ai: from 0.6.0 before 1.0.0. |
| GitLab has remediated an issue in GitLab EE affecting all versions from 11.10 before 19.1.7, 19.2 before 19.2.5, and 19.3 before 19.3.1 that, under certain conditions, an authenticated user could have caused denial of service, due to an unbounded loop triggered by specially crafted input in the SCIM user provisioning feature. |
| A vulnerability was identified in bytebot-ai bytebot 0.0.1. The affected element is an unknown function of the component Agent Execution Workflow. Such manipulation leads to infinite loop. The attack may be performed from remote. The exploit is publicly available and might be used. This vulnerability only affects products that are no longer supported by the maintainer. |
| ORAS (OCI Registry As Storage) is a CLI and library for managing artifacts in OCI registries. In ORAS CLI versions up to and including 1.3.2, the recursive referrer traversal does not track visited descriptors, so a malicious OCI registry that returns a cyclic referrer graph causes unbounded recursion and memory growth. This affects oras discover, whose recursive traversal is enabled by default because the --depth option defaults to 0 (unlimited), as well as the recursive referrer counting used by the oras backup and oras restore workflows. A cyclic graph can be as simple as A referring to B and B referring back to A. A malicious registry can use this to cause a client-side denial of service, exhausting CPU and memory and hanging automation or CI/CD pipelines that run ORAS against untrusted registry metadata. The vulnerability does not extend to code execution, artifact substitution, or integrity bypass. This issue has been fixed in version 1.3.3. |
| iskorotkov/avro is a fast Go Avro codec. Prior to 2.33.0, the Avro array and map decoders looped over an attacker-controlled block-count value without checking the underlying reader's error state inside the loop body. Reader.ReadBlockHeader returns the count as a Go int, which is 64-bit on amd64 / arm64 targets — so a producer can declare a block of up to math.MaxInt64 (~9.2 × 10¹⁸) elements followed by EOF (or any truncated payload), and the decoder will attempt that many no-op iterations before propagating the error. The realistic ceiling is "indefinite until the worker is killed externally" — a single hostile payload pins a CPU core until the process is OOM-killed, deadline-cancelled, or terminated. Remote, unauthenticated denial-of-service. This vulnerability is fixed in 2.33.0. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: qcom-geni: fix TX DMA buffer flush
When transmit flushing a qcom-geni UART during an ongoing TX DMA, the
UART gets stuck infinitely repeating corrupted TX DMA frames.
The DMA-mode uart_ops does not provide a flush_buffer callback, so an
in-flight transfer can complete after serial core has reset the transmit
kfifo, underflowing its length and resubmitting page-sized transfers
indefinitely. Add one that stops the transfer and clears tx_remaining
and tx_queued.
The stop path was also broken: it unmapped the buffer while the serial
engine could still read it, and never reset the TX DMA state machine.
Cancel the main sequencer command first, then reset the state machine
and wait for it before unmapping. Drop the early return so a pending
mapping is also cleaned up when the main command is inactive.
The bug can be triggered from userspace with a large write immediately
followed by TCOFLUSH. A following tcdrain will hang forever. The bug was
reproduced and this fix was validated on Arduino Uno Q (QRB2210)
using /dev/ttyHS1. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix another iunlink infinite loop bug in online fsck
xrep_iunlink_resolve_bucket is supposed to reconstruct as much of the
incore prev and next unlinked list pointers based on what it finds on
disk and in memory before we move on to relinking the truly lost inodes
back into the unlinked list. However, it's still vulnerable to infinite
loops that come in via the next_unlinked pointers.
Fix this problem by remembering which inodes we've already seen and
checking new agino pointers against that. If a bit is already set,
either this is a loop or the inode has nonzero link count. We'll deal
with the second case in a subsequent patch. |
| Rejected because the CVE description attributes a vulnerability to a non-existent Linux kernel function (usb_giveback_urb()) and the reported issue cannot be mapped to any valid codebase. |
| GNU wget is vulnerable to denial of service in its FTP OPIE/S-KEY authentication functionality. The server-supplied sequence number from the FTP challenge line is used as an iteration count for an MD5 key-derivation loop without any upper bound validation. A malicious FTP server or a network attacker positioned to intercept FTP traffic can send a crafted OPIE challenge with a sequence number near INT_MAX, causing wget to perform up to approximately 2.1 billion MD5 computations and suspend for some time. The --timeout option does not mitigate this because it applies only to network I/O, not CPU computation.
This issue was fixed in commit e9697d98e7249b0f68a6be040a4f3dcc5bc101fa |
| LiquidJS is a Shopify / GitHub Pages compatible template engine in pure JavaScript. From 10.26.0 until 10.27.1, the strip_html filter in src/filters/html.ts can enter an infinite loop when an input string contains <, includes at least one preceding character, and has no later >. In strip_html, the search for the next opener advances lt while the loop index remains unchanged when the closer search returns -1, and the equality-only stall guard does not exit because the loop index is less than lt. Reprocessing the same state indefinitely blocks template rendering and can cause denial of service with an input as short as a<. This issue is fixed in version 10.27.1. |
| Picotls is a TLS protocol library that allows users select different crypto backends based on their use case. Picotls implements its own ASN.1 validation helper, which is used by the minicrypto backend while parsing local PKCS#8 private keys. Prior to commit c14231d801407640bc42c2dcf92783409ea6a7c7, the validator recursively descends into constructed ASN.1 elements without enforcing a maximum nesting depth. If an application loads an attacker-supplied private-key file through ptls_minicrypto_load_private_key(), or otherwise calls the public ASN.1 validation API on untrusted DER, a crafted deeply nested ASN.1 structure can exhaust the process stack and crash the application. Note that the libcrypto (OpenSSL) backend does not use the ASN.1 validation helper of picotls, and therefore is immune to this vulnerability. The vulnerability has been addressed in commit c14231d801407640bc42c2dcf92783409ea6a7c7. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: xilinx: use FIFO occupancy register to determine buffer size
The method the driver uses to determine the size of the FIFO has a
problem. What it currently does is this:
It stops the SPI hardware and writes to the TX FIFO register until TX
FIFO FULL asserts in the status register. But the hardware does not only
have the FIFO, it also has a shift register which can hold a byte. This
can be seen, when writing a byte to the FIFO (while the SPI hardware is
stopped,) the TX FIFO EMPTY is still empty. So, if we have a FIFO size
of 16 for example, the current method returns a 17.
This is a problem, at least when using the driver in irq mode. The same
size determined for the TX FIFO is also assumed for the RX FIFO. When a
SPI transaction wants to write the amount of the FIFO size or more
bytes, the following happens, for example with 16 bytes FIFO size:
The driver stops the SPI hardware and writes 17 bytes to the TX FIFO and
starts the SPI hardware and goes sleep.
The hardware then shifts out 17 bytes (FIFO + shift register) and
simultaneously reads bytes into the RX FIFO, but it only has 16 places,
so it looses one byte. Then TX FIFO empty asserts, wakes the driver
again, which has a fast path and reads 16 bytes from the RX FIFO, but
before reading the last 17th byte (which is lost) it does this:
sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
if (!(sr & XSPI_SR_RX_EMPTY_MASK)) {
xilinx_spi_rx(xspi);
rx_words--;
}
It reads the status register and checks if the RX FIFO is not empty.
But it is empty in our case. So this check spins in a while loop
forever locking the driver.
This patch fixes the logic to determine the FIFO size. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix potential infinite loop in rxrpc_recvmsg()
Fix the wait in rxrpc_recvmsg() also take check the oob queue. |
| django CMS is an easy-to-use and developer-friendly enterprise content management system powered by Django. Prior to 5.0.8, the move_plugin endpoint in cms/admin/placeholderadmin.py accepts an attacker-controlled plugin_parent value without rejecting a plugin’s own identifier or a descendant identifier. A staff user with plugin-change permission under CMS_PERMISSION can create a parent_id cycle in the plugin tree. The _get_descendants_cte and _get_ancestors_cte queries in cms/models/pluginmodel.py have no cycle guard, so get_descendants() and later rendering, copy, or delete operations can recurse indefinitely or reach a database recursion limit, corrupting the tree and consuming request workers. This issue is fixed in versions 5.0.8. |
| Multiple Cisco products are affected by a vulnerability in the Snort 3 VBA feature that could allow an unauthenticated, remote attacker to cause the Snort 3 Detection Engine to crash.
This vulnerability is due to improper error checking when decompressing VBA data. An attacker could exploit this vulnerability by sending crafted VBA data to the Snort 3 Detection Engine on the targeted device. A successful exploit could allow the attacker to cause the Snort 3 Detection Engine to enter an infinite loop, causing a DoS condition. |
