| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
squashfs: Add dictionary size range check to prevent shift-out-of-bounds
When an abnormal SquashFS image (COMP_OPTS flag is 1 but dictionary size
is 0) is mounted, and performs shift operations using dictionarysize, the
shift exponent is -1, causing a shift-out-of-bounds.
Detail as below:
squashfs_comp_opts(msblk, buffer, length)
squashfs_xz_comp_opts()
if (comp_opts)
n = ffs(opts->dict_size) - 1;<----opts->dict_size=0, n=-1
if (opts->dict_size != (1 << n) && opts->dict_size !=
(1 << n) + (1 << (n + 1))) <----shift-out-of-bounds
Fix it by adding a dictionary size range check before the shift operation. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: pac1934: check ACPI label duplication
A label duplication failure currently reaches the terminating-byte
write. Release the ACPI result and abort before accessing the missing
label; earlier labels are managed by devres.
Detected by static analysis and reviewed with AI-assisted source auditing. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: kionix-kx022a: Prevent memory leak and fix state
The driver allocates memory for samples at buffer enable path. If regmap
operation fails in the kx022a_fifo_enable() at the buffer enable path, the
allocated memory is never freed. Furthermore, the state information and
previous hardware configuration(s) aren't undone, potentially leaving
WMI interrupts and buffers enabled, or driver state flags wrong.
Free the memory and revert the hardware configuration and state flags on
error path. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Don't access a DP tunnel after its DPRX read was canceled
tb_dp_dprx_work() checks ->dprx_canceled before it takes tb->lock so it
misses a tb_dp_dprx_stop() that could not cancel the already running
work. It then polls the DPRX capabilities and runs the callback for a
tunnel that has already been torn down while the domain is suspending or
going away.
This can be hit by cancelling the DPRX read from outside the ordered
tb->wq: During suspend tb_disconnect_and_release_dp() does just this and
with a later patch tb_stop() will do it as well. The latter in combination
with the Apple NHI where the DPRX read never completed is how I hit
this.
Check the flag with tb->lock held instead and check it again in
tb_dp_tunnel_active() because the callback runs after the lock has been
dropped again.
Also clear the flag in tb_dp_dprx_start() so that it only ever describes
the work that is currently in flight. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Fix domain reference leak when DPRX read is canceled
tb_tunnel_one_dp() takes a domain reference which is only dropped once
tb_dp_tunnel_active() has run on the work queue. If that work is
cancelled that reference is leaked. Since
commit f5cc545f5969 ("thunderbolt: Wait for tb_domain_release() to
complete when driver is removed") instead of just leaking memory this
now also blocks in the completion wait forever when unbinding the
driver.
This can be triggered whenever a DP tunnel is torn down before the DPRX
read has completed, e.g. by unplugging within the timeout, and then
unbinding the driver.
That reference only exists to keep the domain around while the DPRX work
is scheduled so let the work itself own it: take it in tb_dp_dprx_start()
and drop it in both places that end the work. Get/put are then paired
inside the same file and it doesn't matter anymore if the callback ever
runs. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Tear down inactive DP tunnels when the domain is stopped
tb_stop() only tears down DMA tunnels so a DP tunnel that is still
waiting for dprx_work to complete keeps that work queued while the
routers are removed and the control channel is stopped. The work only
stops once the DPRX timeout has passed and because it requeues itself
until then the flush_workqueue() in tb_domain_remove() won't wait for its
final run. The callback then runs against a domain that is already torn
down. A reference to that domain is kept so the completion waiting for
that domain to disappear in unbind will block until the timeout is
eventually reached.
Tear down DP tunnels that are not active yet as well which also cancels
that work. Tunnels for displays that are already alive are untouched and
keep working. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Wait for an RCU tasks grace period before freeing trampoline progs
When a prog is detached from a trampoline, it is freed after an RCU
grace period, or an RCU tasks trace one if it is sleepable. This covers
the tasks that are running the prog, since the prog's enter helper takes
the matching read lock before the prog is called. On a preemptible
kernel, it doesn't cover a task that was preempted in the trampoline
just before the enter helper. That task holds no lock yet, and it calls
the prog after it was freed:
BUG: KASAN: vmalloc-out-of-bounds in __bpf_prog_enter_recur+0x3a5/0x3f0
Read of size 8 at addr ffffc90000055040 by task candidate/110
CPU: 1 UID: 0 PID: 110 Comm: candidate Not tainted 7.3.0-rc2-00014-g15071f2a1263-dirty #2 PREEMPT(full)
Call Trace:
<TASK>
__bpf_prog_enter_recur+0x3a5/0x3f0
bpf_trampoline_6442509193+0x37/0xf1
__x64_sys_futex+0x9/0x410
do_syscall_64+0xb0/0x530
...
Wait for an RCU tasks grace period before the existing one when freeing
a prog that was linked to a trampoline. An RCU tasks grace period only
ends once the tasks that were preempted have run again, and
bpf_tramp_image_put() already relies on it to free the image. It doesn't
wait for tasks that sleep in the trampoline, the next commit takes care
of those.
Only progs that were linked to a trampoline can be called this way, so
bpf_trampoline_add_prog() marks them and other progs are still freed as
before. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: pressure: rohm-bm1390: Return error when read fails
The data reading function ignores the cached error value, and
unconditionally returns 0. Return cached 'ret' -value after stopping
the measurement so user knows if read failed and data is garbage. |
| In the Linux kernel, the following vulnerability has been resolved:
fprobe: Use guard(rcu_sched_notrace) and check rcu_is_watching()
unregister_fprobe() and unregister_fprobe_async() (used by BPF
kprobe-multi) rely on standard RCU grace periods (synchronize_rcu()
and call_rcu()) to wait until in-flight fprobe handlers complete before
freeing the fprobe.
However, if an fprobe handler executes while RCU is not watching (such
as in the idle loop or nohz_full extended quiescent states), standard
RCU does not track preemption-disabled sections. Consequently,
synchronize_rcu() does not wait for those executions, which can lead
to a use-after-free if the fprobe is freed immediately after
unregistration. Ensure handlers exit early when !rcu_is_watching().
Furthermore, fprobe_fgraph_entry() and fprobe_ftrace_entry() previously
used guard(rcu)() and rcu_read_lock(), which invoke lockdep on every
hit under CONFIG_PROVE_LOCKING. This adds overhead and can cause lockdep
recursion if probed functions interact with lockdep.
Since rhltable_lookup() and rhl_for_each_entry_rcu() use
rcu_dereference_all_check() (which checks rcu_read_lock_any_held()),
holding preemption disabled via rcu_read_lock_sched_notrace() is fully
valid and sufficient so long as rcu_is_watching() is true.
Define and use guard(rcu_sched_notrace)() across fprobe_ftrace_entry(),
fprobe_fgraph_entry(), and fprobe_return(). This eliminates fast-path
rcu_read_lock() and lockdep overhead while guaranteeing safe grace
period synchronization. |
| In the Linux kernel, the following vulnerability has been resolved:
thunderbolt: Hold a router reference for each allocated HopID
tb_stop() drops the reference to all DP tunnels but does not deactivate
them, thus nothing cancels a dprx_work still in flight (which holds its
own tunnel reference) and the tunnel can outlive tb_switch_remove(). The
HopID releases in tb_path_free() then operate on freed IDAs and trigger
warnings like
ida_free called for id=8 which is not allocated.
This can be triggered by unbinding the driver while a DP tunnel is still
waiting for the DPRX capabilities read to finish. On the Apple NHI
unplugging the cable runs into just that reliably because the read can
never finish right now and because the unplug powers down the entire
USB4 complex and removes the NHI device.
Take a router reference whenever an input or output HopID is allocated
and drop it again after the HopID is released. This keeps the ports and
their HopID IDAs alive for as long as they are used.
The KUnit tests allocate routers without ever registering their devices
so initialize the embedded struct device there as well and drop its
initial reference when the test is finished. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/vcn: set no_user_fence for VCN v5.0.1 enc ring
VCN encoder and decoder rings do not support 64-bit user fence writes,
reject CS submissions with user fences.
(cherry picked from commit e16be95a2c3ee712b142cb27d2dca0b461181359) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/jpeg: set no_user_fence for JPEG v4.0.5 ring
JPEG rings do not support 64-bit user fence writes, reject CS
submissions with user fences.
(cherry picked from commit f05d0a4f21fc720116d6e238f23308b199891058) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/jpeg: set no_user_fence for JPEG v5.0.0 ring
JPEG rings do not support 64-bit user fence writes, reject CS
submissions with user fences.
(cherry picked from commit 0f43893d3cd478fa57836697525b338817c9c23d) |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: use kvfree() for replaced sysctl write buffer
proc_sys_call_handler() allocates its temporary sysctl buffer with
kvzalloc() and passes it to __cgroup_bpf_run_filter_sysctl(). Since
kvzalloc() may fall back to vmalloc() for large allocations, freeing
that buffer with kfree() is wrong and can corrupt memory.
Use kvfree() to safely handle both kmalloc and kvzalloc()/vmalloc
allocations.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1-rc5.
Reproduced the bug based on v7.1-rc4 in a QEMU x86_64 guest booted with
KASAN and CONFIG_FAILSLAB enabled. To exercise the replacement path, the
test tree also included the accompanying fix for the stale ret == 1
check in __cgroup_bpf_run_filter_sysctl(). The reproducer confines
failslab injections to the proc_sys_call_handler() range, uses
stacktrace-depth=32, and injects fail-nth=1 while writing 8191 bytes to
/proc/sys/kernel/domainname from a task in the target cgroup. Under
that setup, fail-nth=1 triggered the fault:
BUG: unable to handle page fault for address: ffffeb0200024d48
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 SMP KASAN NOPTI
CPU: 2 UID: 0 PID: 209 Comm: repro_proc_sys_ Not tainted 7.1.0-rc4-00686-g97625979a5d4 PREEMPT(lazy)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
RIP: 0010:kfree+0x6e/0x510
...
Call Trace:
<TASK>
? __cgroup_bpf_run_filter_sysctl+0x626/0xc30
__cgroup_bpf_run_filter_sysctl+0x74d/0xc30
? __pfx___cgroup_bpf_run_filter_sysctl+0x10/0x10
? srso_return_thunk+0x5/0x5f
? __kvmalloc_node_noprof+0x345/0x870
? proc_sys_call_handler+0x250/0x480
? srso_return_thunk+0x5/0x5f
proc_sys_call_handler+0x3a2/0x480
? __pfx_proc_sys_call_handler+0x10/0x10
? srso_return_thunk+0x5/0x5f
? selinux_file_permission+0x39f/0x500
? srso_return_thunk+0x5/0x5f
? lock_is_held_type+0x9e/0x120
vfs_write+0x98e/0x1000
...
</TASK>
With this fix applied on top of the same test setup, rerunning the
reproducer with fail-nth=1 yields no corresponding Oops reports. |
| In the Linux kernel, the following vulnerability has been resolved:
keys: Pin request_key_auth payload in instantiate paths
A: request_key() B: KEYCTL_INSTANTIATE_IOV
================ =========================
create auth key
store rka in auth key
wait for helper
get auth key
load rka from auth key
copy user payload
sleep on #PF
helper completed
detach and free rka
destroy auth key
wake up
use rka->target_key
**USE-AFTER-FREE**
Give request_key_auth payloads a refcount. Take a payload reference while
authkey->sem stabilizes the payload and revocation state. Hold that
reference across the instantiate and reject paths. Drop the auth key
owning reference from revoke and destroy.
[jarkko: Replaced the first two paragraphs of text with an actual
concurrency scenario.] |
| In the Linux kernel, the following vulnerability has been resolved:
net: ip_gre: require CAP_NET_ADMIN in the device netns for changelink
A tunnel changelink() operates on at most two netns, dev_net(dev) and
the tunnel link netns t->net. They differ once the device is created in
or moved to a netns other than the one the request runs in. The rtnl
changelink path checks CAP_NET_ADMIN only against dev_net(dev), so a
caller privileged there but not in t->net can rewrite a tunnel that
lives in t->net.
Add rtnl_dev_link_net_capable() next to rtnl_get_net_ns_capable() in
net/core/rtnetlink.c. It requires CAP_NET_ADMIN in the link netns and is
skipped when the link netns is dev_net(dev), where the rtnl path already
checked it. The other patches in this series use the same helper.
Gate ipgre_changelink() and erspan_changelink() with it, at the top of
the op before any attribute is parsed, because the parsers update live
tunnel fields first. ipgre_netlink_parms() sets t->collect_md before
ip_tunnel_changelink() runs.
Commit 8b484efd5cb4 ("ip6: vti: Use ip6_tnl.net in
vti6_siocdevprivate().") added the same check on the ioctl path. This
adds it on RTM_NEWLINK. |
| In the Linux kernel, the following vulnerability has been resolved:
net: skmsg: preserve sg.copy across SG transforms
The sk_msg sg.copy bitmap is part of the scatterlist entry ownership
state. A set bit tells sk_msg_compute_data_pointers() not to expose the
entry through writable BPF ctx->data. This protects entries backed by
pages that are not private to the sk_msg, such as splice-backed file
page-cache pages.
Several sk_msg transform paths move, copy, split, or compact
msg->sg.data[] entries without moving the matching sg.copy bit. This can
make an externally backed entry arrive at a new slot with a clear copy
bit. A later SK_MSG verdict can then expose sg_virt(sge) as writable
ctx->data and BPF stores can modify the original page cache.
Keep sg.copy synchronized with sg.data[] whenever entries are
transferred, shifted, split, or copied into a new sk_msg. Clear the bit
when an entry is replaced by a newly allocated private page or freed.
This covers the BPF pull/push/pop helpers, sk_msg_shift_left/right(),
sk_msg_xfer(), and tls_split_open_record(), including the partial tail
entry created during TLS open-record splitting. |
| In the Linux kernel, the following vulnerability has been resolved:
watchdog: msc313e: Fix NULL pointer dereference in PM callbacks
msc313e_wdt_probe() doesn't set the driver data for the platform device.
As a result, dev_get_drvdata() in msc313e_wdt_suspend() and
msc313e_wdt_resume() will return NULL, leading to a NULL pointer
dereference afterward.
Set the platform device driver data in msc313e_wdt_probe(). |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: mdb: Fix use-after-free in vxlan_mdb_remote_src_del()
vxlan_mdb_is_valid_source(), which validates MDBE_ATTR_SOURCE and every
MDBE_ATTR_SRC_LIST member, accepts the all-zeros address.
A source list is only accepted on a (*, G) entry, whose source is the
all-zeros address, and for each member of the list an (S, G) entry is
derived from it by substituting the source. Entries are keyed by a plain
memcmp() of struct vxlan_mdb_entry_key, so if MDBE_ATTR_SOURCE is present
and holds the all-zeros address and the source list holds it as well, the
derived (S, G) key is byte-identical to the (*, G) key and resolves to the
same entry. Omitting MDBE_ATTR_SOURCE is not equivalent, as the key is
then left with a zero address family.
vxlan_mdb_remote_src_del() removes the forwarding entry of a source before
freeing the source entry:
vxlan_mdb_remote_src_fwd_del(vxlan, group, remote, &ent->addr);
vxlan_mdb_remote_src_entry_del(ent);
With the keys aliased, the first call deletes the remote of the entry that
owns 'ent' instead of a separate (S, G) entry, and frees 'ent'. The second
call then runs on the freed entry, and its hlist_del() reads ->pprev and
->next out of it and writes through them.
Adding the (*, G) entry with NLM_F_REPLACE and no source list marks the
all-zeros source for deletion and reaches this from the sweep at the end
of vxlan_mdb_remote_srcs_replace().
BUG: KASAN: slab-use-after-free in __vxlan_mdb_add+0x1cd/0xd70
Read of size 8 at addr ffff888102852500 by task poc/84
__vxlan_mdb_add+0x1cd/0xd70
vxlan_mdb_add+0xc0/0x140
rtnl_mdb_add+0x157/0x2a0
rtnetlink_rcv_msg+0x207/0x5a0
Allocated by task 84:
__kmalloc_cache_noprof+0x153/0x360
vxlan_mdb_remote_srcs_add+0x2eb/0x440
__vxlan_mdb_add+0x803/0xd70
Freed by task 84:
kfree+0x14c/0x3b0
vxlan_mdb_remote_del+0x129/0x1a0
__vxlan_mdb_del+0x4f/0xe0
vxlan_mdb_remote_src_fwd_del.isra.0+0x162/0x1b0
__vxlan_mdb_add+0x1c5/0xd70
The MDB operations are netns-scoped, so an unprivileged user can perform
them in a new user and network namespace.
Reject the all-zeros address in vxlan_mdb_is_valid_source(), which covers
both call sites. A (*, G) entry is expressed by omitting the source, so
nothing legitimate is refused.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: fix soft lockup from unpadded ASCONF-ACK parameter iteration
sctp_verify_asconf() walks ASCONF-ACK parameters with
sctp_walk_params(), which advances by SCTP_PAD4(length), while the
consumer sctp_get_asconf_response() iterates the same parameters
advancing by the raw length, without padding. A single odd-length
parameter desynchronises the two walks and makes the consumer
interpret attacker-controlled bytes at a misaligned offset.
When those bytes yield a length of zero, the while loop over
asconf_ack_len makes no progress, spinning forever in softirq
context, and the watchdog reports a soft lockup. All reads stay
within the received skb, so the lockup is a pure remote denial of
service. A remote peer can trigger it with a crafted ASCONF-ACK on
an ADD-IP enabled association with an outstanding ASCONF (RFC 5061
section 4.1.2 requires the chunk to be authenticated, but the
predefined empty key id 0 allows the peer to compute the same
association HMAC from publicly exchanged parameters, so the gate
does not help).
The SCTP_PARAM_ERR_CAUSE case of sctp_verify_asconf() also performs
no length check, letting a parameter without a complete error
header reach the consumer, which reads errhdr.cause past the end of
the parameter, an out-of-bounds read.
Reject SCTP_PARAM_ERR_CAUSE parameters shorter than
sizeof(struct sctp_addip_param) + sizeof(struct sctp_errhdr) at the
verifier, and advance the consumer iterator with the same padding
rule as the verifier to keep the two walks in lockstep. The verifier
change guarantees a complete error header in every ERR_CAUSE
parameter the consumer can see, so the consumer's asconf_ack_len
check is dropped and it returns err_param->cause directly. The
consumer padding fix is still required because odd lengths remain
valid for SCTP_PARAM_ERR_CAUSE per RFC 5061.
The issue was found by ZeroHive, a vulnerability hunting agent at
Tencent Yunding Lab. |
