| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| An Improper Check for Unusual or Exceptional Conditions vulnerability in the
advanced forwarding toolkit (evo-aftmand)
of Juniper Networks Junos OS Evolved on PTX Series allows an unauthenticated network-based attacker generating continuous routing updates, resulting in unilist ECMP routes, to crash the
evo-aftmand process on the PFE, leading to a Denial-of-Service (DoS). The conditions required for successful exploitation are based on a sequence of events that are outside an attacker's direct control.
Unified list (unilist) ECMP routes are a specific ECMP behavior where multiple equal-cost routes share a single logical next-hop list entry. The router treats them as one route with multiple next hops and load balances traffic across that unified list. Due to an issue processing unilist ECMP routing updates, internal state corruption may occur, especially in large-scale ECMP unilist deployments, leading to the evo-aftmand process crashing, resulting in an evo-aftmand-bx core. Manual intervention is required to recover by rebooting the system or restarting the FPC.
This issue affects Junos OS Evolved on PTX :
* from 24.4R2-EVO before 24.4R2-S3-EVO;
* from 25.2 before 25.2R2-EVO. |
| An Out-of-bounds Write vulnerability in the SNMP daemon (snmpd) of Juniper Networks Junos OS and Junos OS Evolved allows an authenticated network-based attacker sending specific valid SNMPv3 queries to trigger a memory leak. Over time, continuous receipt of these queries will result in snmpd process memory exhaustion, resulting in a process crash and restart, impacting the ability to monitor the system via SNMP.
Memory usage can be monitored using the following command:
user@device> show system processes extensive | match snmpd
This issue affects:
Junos OS:
* all versions before 21.2R3-S8;
* from 21.4 before 21.4R3-S7;
* from 22.1 before 22.1R3-S6;
* from 22.2 before 22.2R3-S4;
* from 22.3 before 22.3R3-S3;
* from 22.4 before 22.4R3-S2;
* from 23.2 before 23.2R2;
* from 23.4 before 23.4R2.
Junos OS Evolved:
* all versions before 21.2R3-S8-EVO;
* from 21.4 before 21.4R3-S7-EVO;
* all versions of 22.1-EVO,
* from 22.2 before 22.2R3-S4-EVO;
* from 22.3 before 22.3R3-S3-EVO;
* all versions of 22.4-EVO,
* from 23.2 before 23.2R2-EVO;
* from 23.4 before 23.4R2-EVO. |
| An Improper Check for Unusual or Exceptional Conditions vulnerability in the routing protocol daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows an adjacent, unauthenticated attacker sending a specific BGP update over an established BGP session to cause a Denial-of-Service (DoS).
Upon receipt of a specifically malformed non-inet/inet6 unicast BGP update, an RPD crash and restart is triggered, which will cause a complete service outage until routing has reconverged. The rpd crash occurs before the update can be readvertised, so there is no downstream propagation.
This issue affects:
* Junos OS versions 25.2 before 25.2R2;
* Junos OS Evolved versions 25.2 before 25.2R2-EVO.
This issue doesn't affect Junos OS versions before 25.2R1 nor Junos OS Evolved versions before 25.2R1-EVO. |
| An Improper Restriction of Communication Channel to Intended Endpoints vulnerability in Juniper Networks Junos OS Evolved allows an unauthenticated, network-based attacker to cause a limited information disclosure and availability impact to the device.
Due to a wrong initialization, a process which should only be able to communicate internally within the device can be reached over the network via an open port. This leads to a device being inadvertently exposed and increased CPU cycles spent processing ingress packets.
This issue affects Junos OS Evolved:
* all versions before 23.2R2-S7-EVO,
* 23.4 versions before 23.4R2-S8-EVO,
* 24.2 versions before 24.2R2-S5-EVO,
* 24.4 versions before 24.4R2-S4-EVO,
* 25.2 versions before 25.2R2-S1-EVO,
* 25.4 versions before 25.4R1-S2-EVO. |
| An Improper Validation of Specified Quantity in Input vulnerability in the Packet Forwarding Engine (pfe) of Juniper Networks Junos OS on MX Series allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS).
When a specific packet is received from device in the same broadcast domain, an affected system calculates the packet size incorrectly. This causes further packet processing to fail, which triggers an FPC major error, resulting in a FPC reset impacting traffic until the FPC has automatically recovered.
Affected scenarios are: MAP-T, or non-IP traffic encapsulated in IP (e.g. MPLS over GRE).
When this issue happens the following logs can be observed:
fpc<#> CMError: /fpc/0/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_LI_INT_REG_UNROLL_TAIL_LENGTH_OVF (0x2205eb), scope: pfe, category: functional, severity: major, module: MQSS(0), type: LI: Unroll TAIL length overflow, oc_category: default
fpc<#> Performing action reset-fru for error /fpc/0/pfe/0/cm/0/MQSS(0)/0/MQSS_CMERROR_LI_INT_REG_UNROLL_TAIL_LENGTH_OVF (0x2205eb) in module: MQSS(0) with scope: pfe category: functional level: major, oc_category: default
This issue affects Junos OS on MX Series:
* all versions before 23.2R2-S6,
* 23.4 versions before 23.4R2-S7,
* 24.2 versions before 24.2R2-S4,
* 24.4 versions before 24.4R2-S4,
* 25.2 versions before 25.2R2. |
| An Improper Check for Unusual or Exceptional Conditions vulnerability in the packet forwarding engine (pfe) of Juniper Networks Junos OS on QFX10000 Series allows an unauthenticated, adjacent attacker to cause a Denial-of-Service (DoS).
On all QFX10000 platforms in an EVPN-VxLAN scenario, if an attacker sends IPv6 multicast traffic and these packets reach the non-IRB interface of a spine switch it floods the packet to other spines and all Ethernet Segment Identifier (ESI) leaf switches. This flooding causes the packet to be forwarded in a endless loop, which can lead to saturation of the involved links and in turn impact to legitimate traffic.
This issue affects Junos OS on QFX10000 Series:
* all versions before 23.2R2-S7,
* 23.4 versions before 23.4R2-S8,
* 24.2 versions before 24.2R2-S4,
* 24.4 versions before 24.4R2-S4.
This issue does not affect Junos version after 24.4 as the QFX10000 Series devices are not supported on newer versions anymore. |
| A Missing Authorization vulnerability in the CLI of Juniper Networks Junos OS on EX Series allows a local, authenticated attacker to cause a Denial-of-Service (DoS).
On EX2300, EX4000, EX4100, EX4300-MP (Multigigabit) and EX4400 switches, an authenticated, local attacker with no specific permissions or class can execute a specific, privileged CLI 'request' command which will cause complete traffic impact until the system automatically recovers.
This issue affects Junos OS on EX2300, EX4000, EX4100, EX4300-MP (Multigigabit) and EX4400:
* 23.2R2 versions before 23.2R2-S6,
* 23.4 versions before 23.4R2-S8,
* 24.2 versions before 24.2R2-S4,
* 24.4 versions before 24.4R2-S3,
* 25.2 versions before 25.2R2,
* 25.4 versions before 25.4R1-S1. |
|
An Incomplete Cleanup vulnerability in Nonstop active routing (NSR) component of Juniper Networks Junos OS allows an adjacent, unauthenticated attacker to cause memory leak leading to Denial of Service (DoS).
On all Junos OS platforms, when NSR is enabled, a BGP flap will cause memory leak. A manual reboot of the system will restore the services.
Note: NSR is not supported on the SRX Series and is therefore not affected by this vulnerability.
The memory usage can be monitored using the below commands.
user@host> show chassis routing-engine no-forwarding
user@host> show system memory | no-more
This issue affects:
Juniper Networks Junos OS
* 21.2 versions earlier than 21.2R3-S5;
* 21.3 versions earlier than 21.3R3-S4;
* 21.4 versions earlier than 21.4R3-S4;
* 22.1 versions earlier than 22.1R3-S2;
* 22.2 versions earlier than 22.2R3-S2;
* 22.3 versions earlier than 22.3R2-S1, 22.3R3;
* 22.4 versions earlier than 22.4R1-S2, 22.4R2.
This issue does not affect Junos OS versions earlier than 20.4R3-S7.
|
|
An Improper Check for Unusual or Exceptional Conditions vulnerability in Routing Protocol Daemon (RPD) of Juniper Networks Junos OS and Junos OS Evolved allows a network-based, unauthenticated attacker to cause rpd to crash, leading to Denial of Service (DoS).
On all Junos OS and Junos OS Evolved platforms, when NETCONF and gRPC are enabled, and a specific query is executed via Dynamic Rendering (DREND), rpd will crash and restart. Continuous execution of this specific query will cause a sustained Denial of Service (DoS) condition.
This issue affects:
Juniper Networks Junos OS
* 22.2 versions earlier than 22.2R2-S2, 22.2R3;
* 22.3 versions earlier than 22.3R2, 22.3R3.
Juniper Networks Junos OS Evolved
* 22.2 versions earlier than 22.2R2-S2-EVO, 22.2R3-EVO;
* 22.3 versions earlier than 22.3R2-EVO, 22.3R3-EVO.
This issue does not affect Juniper Networks:
Junos OS versions earlier than 22.2R1;
Junos OS Evolved versions earlier than 22.2R1-EVO.
|
| A Buffer Copy without Checking Size of Input ('Classic Buffer Overflow') vulnerability in the advanced forwarding toolkit (evo-aftmand/evo-pfemand) of Juniper Networks Junos OS Evolved on PTX Series or QFX5000 Series allows an unauthenticated, adjacent attacker to cause a Denial of Service (DoS).An attacker sending crafted multicast packets will cause line cards running evo-aftmand/evo-pfemand to crash and restart or non-line card devices to crash and restart. Continued receipt and processing of these packets will sustain the Denial of Service (DoS) condition.
This issue affects Junos OS Evolved PTX Series:
* All versions before 22.4R3-S8-EVO,
* from 23.2 before 23.2R2-S5-EVO,
* from 23.4 before 23.4R2-EVO,
* from 24.2 before 24.2R2-EVO,
* from 24.4 before 24.4R2-EVO.
This issue affects Junos OS Evolved on QFX5000 Series:
* 22.2-EVO version before 22.2R3-S7-EVO,
* 22.4-EVO version before 22.4R3-S7-EVO,
* 23.2-EVO versions before 23.2R2-S4-EVO,
* 23.4-EVO versions before 23.4R2-S5-EVO,
* 24.2-EVO versions before 24.2R2-S1-EVO,
* 24.4-EVO versions before 24.4R1-S3-EVO, 24.4R2-EVO.
This issue does not affect Junos OS Evolved on QFX5000 Series versions before: 21.2R2-S1-EVO, 21.2R3-EVO, 21.3R2-EVO, 21.4R1-EVO, and 22.1R1-EVO. |
| An Improper Input Validation vulnerability in Juniper Networks Junos OS and Junos OS Evolved allows an unauthenticated, adjacent attacker, sending a specific genuine BGP packet in an already established BGP session to reset only that session causing a Denial of Service (DoS).
An attacker repeatedly sending the packet will sustain the Denial of Service (DoS).This issue affects Junos OS:
* 25.2 versions before 25.2R2
This issue does not affect Junos OS versions before 25.2R1.
This issue affects Junos OS Evolved:
* 25.2-EVO versions before 25.2R2-EVO
This issue does not affect Junos OS Evolved versions before 25.2R1-EVO.
eBGP and iBGP are affected.
IPv4 and IPv6 are affected. |
| Multiple cross-site scripting (XSS) vulnerabilities in the J-Web interface in Juniper JUNOS 8.5R1.14 allow remote authenticated users to inject arbitrary web script or HTML via (1) the JEXEC_OUTID parameter in a JEXEC_MODE_RELAY_OUTPUT action to the jexec program; the (2) act, (3) refresh-time, or (4) ifid parameter to scripter.php; (5) the revision parameter in a rollback action to the configuration program; the m[] parameter to the (6) monitor, (7) manage, (8) events, (9) configuration, or (10) alarms program; (11) the m[] parameter to the default URI; (12) the m[] parameter in a browse action to the default URI; (13) the wizard-next parameter in an https action to the configuration program; or the (14) Contact Information, (15) System Description, (16) Local Engine ID, (17) System Location, or (18) System Name Override SNMP parameter, related to the configuration program. |
| Multiple cross-site scripting (XSS) vulnerabilities in the J-Web interface in Juniper JUNOS 8.5R1.14 allow remote authenticated users to inject arbitrary web script or HTML via the host parameter to (1) the pinghost program, reachable through the diagnose program; or (2) the traceroute program, reachable through the diagnose program; or (3) the probe-limit parameter to the configuration program; the (4) wizard-ids or (5) pager-new-identifier parameter in a firewall-filters action to the configuration program; (6) the cos-physical-interface-name parameter in a cos-physical-interfaces-edit action to the configuration program; the (7) wizard-args or (8) wizard-ids parameter in an snmp action to the configuration program; the (9) username or (10) fullname parameter in a users action to the configuration program; or the (11) certname or (12) certbody parameter in a local-cert (aka https) action to the configuration program. |
| Cross-site scripting (XSS) vulnerability in the J-Web interface in Juniper JUNOS 8.5R1.14 and 9.0R1.1 allows remote attackers to inject arbitrary web script or HTML via the PATH_INFO to the default URI. |
| udev before 1.4.1 does not verify whether a NETLINK message originates from kernel space, which allows local users to gain privileges by sending a NETLINK message from user space. |
| The Device Mapper multipathing driver (aka multipath-tools or device-mapper-multipath) 0.4.8, as used in SUSE openSUSE, SUSE Linux Enterprise Server (SLES), Fedora, and possibly other operating systems, uses world-writable permissions for the socket file (aka /var/run/multipathd.sock), which allows local users to send arbitrary commands to the multipath daemon. |
| Cross-site scripting (XSS) vulnerability in Juniper NetScreen ScreenOS before 5.4r10, 6.0r6, and 6.1r2 allows remote attackers to inject arbitrary web script or HTML via the user name parameter to the (1) web interface login page or the (2) telnet login page. |
| The IPv6 Neighbor Discovery Protocol (NDP) implementation in (1) FreeBSD 6.3 through 7.1, (2) OpenBSD 4.2 and 4.3, (3) NetBSD, (4) Force10 FTOS before E7.7.1.1, (5) Juniper JUNOS, and (6) Wind River VxWorks 5.x through 6.4 does not validate the origin of Neighbor Discovery messages, which allows remote attackers to cause a denial of service (loss of connectivity) or read private network traffic via a spoofed message that modifies the Forward Information Base (FIB). |
| Juniper Networks Secure Access 2000 5.5 R1 (build 11711) allows remote attackers to obtain sensitive information via a direct request for remediate.cgi without certain parameters, which reveals the path in an "Execute failed" error message. |
| Cross-site scripting (XSS) vulnerability in dana-na/auth/rdremediate.cgi in Juniper Networks Secure Access 2000 5.5 R1 build 11711 allows remote attackers to inject arbitrary web script or HTML via the delivery_mode parameter. |
