| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: Intel: avs: Do not share the name pointer between components
By sharing 'name' directly, tearing down components may lead to
use-after-free errors. Duplicate the name to avoid that.
At the same time, update the order of operations - since commit
cee28113db17 ("ASoC: dmaengine_pcm: Allow passing component name via
config") the framework does not override component->name if set before
invoking the initializer. |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: Correctly handle Rx checksum offload errors
The stmmac_rx function would previously set skb->ip_summed to
CHECKSUM_UNNECESSARY if hardware checksum offload (CoE) was enabled
and the packet was of a known IP ethertype.
However, this logic failed to check if the hardware had actually
reported a checksum error. The hardware status, indicating a header or
payload checksum failure, was being ignored at this stage. This could
cause corrupt packets to be passed up the network stack as valid.
This patch corrects the logic by checking the `csum_none` status flag,
which is set when the hardware reports a checksum error. If this flag
is set, skb->ip_summed is now correctly set to CHECKSUM_NONE,
ensuring the kernel's network stack will perform its own validation and
properly handle the corrupt packet. |
| In the Linux kernel, the following vulnerability has been resolved:
net: use dst_dev_rcu() in sk_setup_caps()
Use RCU to protect accesses to dst->dev from sk_setup_caps()
and sk_dst_gso_max_size().
Also use dst_dev_rcu() in ip6_dst_mtu_maybe_forward(),
and ip_dst_mtu_maybe_forward().
ip4_dst_hoplimit() can use dst_dev_net_rcu(). |
| In the Linux kernel, the following vulnerability has been resolved:
xen/events: Return -EEXIST for bound VIRQs
Change find_virq() to return -EEXIST when a VIRQ is bound to a
different CPU than the one passed in. With that, remove the BUG_ON()
from bind_virq_to_irq() to propogate the error upwards.
Some VIRQs are per-cpu, but others are per-domain or global. Those must
be bound to CPU0 and can then migrate elsewhere. The lookup for
per-domain and global will probably fail when migrated off CPU 0,
especially when the current CPU is tracked. This now returns -EEXIST
instead of BUG_ON().
A second call to bind a per-domain or global VIRQ is not expected, but
make it non-fatal to avoid trying to look up the irq, since we don't
know which per_cpu(virq_to_irq) it will be in. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: use RCU in ip6_output()
Use RCU in ip6_output() in order to use dst_dev_rcu() to prevent
possible UAF.
We can remove rcu_read_lock()/rcu_read_unlock() pairs
from ip6_finish_output2(). |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: use RCU in ip6_xmit()
Use RCU in ip6_xmit() in order to use dst_dev_rcu() to prevent
possible UAF. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp_metrics: use dst_dev_net_rcu()
Replace three dst_dev() with a lockdep enabled helper. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: n_gsm: Don't block input queue by waiting MSC
Currently gsm_queue() processes incoming frames and when opening
a DLC channel it calls gsm_dlci_open() which calls gsm_modem_update().
If basic mode is used it calls gsm_modem_upd_via_msc() and it
cannot block the input queue by waiting the response to come
into the same input queue.
Instead allow sending Modem Status Command without waiting for remote
end to respond. Define a new function gsm_modem_send_initial_msc()
for this purpose. As MSC is only valid for basic encoding, it does
not do anything for advanced or when convergence layer type 2 is used. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: reject index allocation if $BITMAP is empty but blocks exist
Index allocation requires at least one bit in the $BITMAP attribute to
track usage of index entries. If the bitmap is empty while index blocks
are already present, this reflects on-disk corruption.
syzbot triggered this condition using a malformed NTFS image. During a
rename() operation involving a long filename (which spans multiple
index entries), the empty bitmap allowed the name to be added without
valid tracking. Subsequent deletion of the original entry failed with
-ENOENT, due to unexpected index state.
Reject such cases by verifying that the bitmap is not empty when index
blocks exist. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wilc1000: avoid buffer overflow in WID string configuration
Fix the following copy overflow warning identified by Smatch checker.
drivers/net/wireless/microchip/wilc1000/wlan_cfg.c:184 wilc_wlan_parse_response_frame()
error: '__memcpy()' 'cfg->s[i]->str' copy overflow (512 vs 65537)
This patch introduces size check before accessing the memory buffer.
The checks are base on the WID type of received data from the firmware.
For WID string configuration, the size limit is determined by individual
element size in 'struct wilc_cfg_str_vals' that is maintained in 'len' field
of 'struct wilc_cfg_str'. |
| In the Linux kernel, the following vulnerability has been resolved:
ptp: ocp: fix use-after-free bugs causing by ptp_ocp_watchdog
The ptp_ocp_detach() only shuts down the watchdog timer if it is
pending. However, if the timer handler is already running, the
timer_delete_sync() is not called. This leads to race conditions
where the devlink that contains the ptp_ocp is deallocated while
the timer handler is still accessing it, resulting in use-after-free
bugs. The following details one of the race scenarios.
(thread 1) | (thread 2)
ptp_ocp_remove() |
ptp_ocp_detach() | ptp_ocp_watchdog()
if (timer_pending(&bp->watchdog))| bp = timer_container_of()
timer_delete_sync() |
|
devlink_free(devlink) //free |
| bp-> //use
Resolve this by unconditionally calling timer_delete_sync() to ensure
the timer is reliably deactivated, preventing any access after free. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: Fix NPD when refreshing an FDB entry with a nexthop object
VXLAN FDB entries can point to either a remote destination or an FDB
nexthop group. The latter is usually used in EVPN deployments where
learning is disabled.
However, when learning is enabled, an incoming packet might try to
refresh an FDB entry that points to an FDB nexthop group and therefore
does not have a remote. Such packets should be dropped, but they are
only dropped after dereferencing the non-existent remote, resulting in a
NPD [1] which can be reproduced using [2].
Fix by dropping such packets earlier. Remove the misleading comment from
first_remote_rcu().
[1]
BUG: kernel NULL pointer dereference, address: 0000000000000000
[...]
CPU: 13 UID: 0 PID: 361 Comm: mausezahn Not tainted 6.17.0-rc1-virtme-g9f6b606b6b37 #1 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014
RIP: 0010:vxlan_snoop+0x98/0x1e0
[...]
Call Trace:
<TASK>
vxlan_encap_bypass+0x209/0x240
encap_bypass_if_local+0xb1/0x100
vxlan_xmit_one+0x1375/0x17e0
vxlan_xmit+0x6b4/0x15f0
dev_hard_start_xmit+0x5d/0x1c0
__dev_queue_xmit+0x246/0xfd0
packet_sendmsg+0x113a/0x1850
__sock_sendmsg+0x38/0x70
__sys_sendto+0x126/0x180
__x64_sys_sendto+0x24/0x30
do_syscall_64+0xa4/0x260
entry_SYSCALL_64_after_hwframe+0x4b/0x53
[2]
#!/bin/bash
ip address add 192.0.2.1/32 dev lo
ip address add 192.0.2.2/32 dev lo
ip nexthop add id 1 via 192.0.2.3 fdb
ip nexthop add id 10 group 1 fdb
ip link add name vx0 up type vxlan id 10010 local 192.0.2.1 dstport 12345 localbypass
ip link add name vx1 up type vxlan id 10020 local 192.0.2.2 dstport 54321 learning
bridge fdb add 00:11:22:33:44:55 dev vx0 self static dst 192.0.2.2 port 54321 vni 10020
bridge fdb add 00:aa:bb:cc:dd:ee dev vx1 self static nhid 10
mausezahn vx0 -a 00:aa:bb:cc:dd:ee -b 00:11:22:33:44:55 -c 1 -q |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Fix memory corruption when FW resources change during ifdown
bnxt_set_dflt_rings() assumes that it is always called before any TC has
been created. So it doesn't take bp->num_tc into account and assumes
that it is always 0 or 1.
In the FW resource or capability change scenario, the FW will return
flags in bnxt_hwrm_if_change() that will cause the driver to
reinitialize and call bnxt_cancel_reservations(). This will lead to
bnxt_init_dflt_ring_mode() calling bnxt_set_dflt_rings() and bp->num_tc
may be greater than 1. This will cause bp->tx_ring[] to be sized too
small and cause memory corruption in bnxt_alloc_cp_rings().
Fix it by properly scaling the TX rings by bp->num_tc in the code
paths mentioned above. Add 2 helper functions to determine
bp->tx_nr_rings and bp->tx_nr_rings_per_tc. |
| In the Linux kernel, the following vulnerability has been resolved:
rcu: Fix rcu_read_unlock() deadloop due to IRQ work
During rcu_read_unlock_special(), if this happens during irq_exit(), we
can lockup if an IPI is issued. This is because the IPI itself triggers
the irq_exit() path causing a recursive lock up.
This is precisely what Xiongfeng found when invoking a BPF program on
the trace_tick_stop() tracepoint As shown in the trace below. Fix by
managing the irq_work state correctly.
irq_exit()
__irq_exit_rcu()
/* in_hardirq() returns false after this */
preempt_count_sub(HARDIRQ_OFFSET)
tick_irq_exit()
tick_nohz_irq_exit()
tick_nohz_stop_sched_tick()
trace_tick_stop() /* a bpf prog is hooked on this trace point */
__bpf_trace_tick_stop()
bpf_trace_run2()
rcu_read_unlock_special()
/* will send a IPI to itself */
irq_work_queue_on(&rdp->defer_qs_iw, rdp->cpu);
A simple reproducer can also be obtained by doing the following in
tick_irq_exit(). It will hang on boot without the patch:
static inline void tick_irq_exit(void)
{
+ rcu_read_lock();
+ WRITE_ONCE(current->rcu_read_unlock_special.b.need_qs, true);
+ rcu_read_unlock();
+
[neeraj: Apply Frederic's suggested fix for PREEMPT_RT] |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix refcount leak causing resource not released
When ksmbd_conn_releasing(opinfo->conn) returns true,the refcount was not
decremented properly, causing a refcount leak that prevents the count from
reaching zero and the memory from being released. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: Fix backlog accounting in qdisc_dequeue_internal
This issue applies for the following qdiscs: hhf, fq, fq_codel, and
fq_pie, and occurs in their change handlers when adjusting to the new
limit. The problem is the following in the values passed to the
subsequent qdisc_tree_reduce_backlog call given a tbf parent:
When the tbf parent runs out of tokens, skbs of these qdiscs will
be placed in gso_skb. Their peek handlers are qdisc_peek_dequeued,
which accounts for both qlen and backlog. However, in the case of
qdisc_dequeue_internal, ONLY qlen is accounted for when pulling
from gso_skb. This means that these qdiscs are missing a
qdisc_qstats_backlog_dec when dropping packets to satisfy the
new limit in their change handlers.
One can observe this issue with the following (with tc patched to
support a limit of 0):
export TARGET=fq
tc qdisc del dev lo root
tc qdisc add dev lo root handle 1: tbf rate 8bit burst 100b latency 1ms
tc qdisc replace dev lo handle 3: parent 1:1 $TARGET limit 1000
echo ''; echo 'add child'; tc -s -d qdisc show dev lo
ping -I lo -f -c2 -s32 -W0.001 127.0.0.1 2>&1 >/dev/null
echo ''; echo 'after ping'; tc -s -d qdisc show dev lo
tc qdisc change dev lo handle 3: parent 1:1 $TARGET limit 0
echo ''; echo 'after limit drop'; tc -s -d qdisc show dev lo
tc qdisc replace dev lo handle 2: parent 1:1 sfq
echo ''; echo 'post graft'; tc -s -d qdisc show dev lo
The second to last show command shows 0 packets but a positive
number (74) of backlog bytes. The problem becomes clearer in the
last show command, where qdisc_purge_queue triggers
qdisc_tree_reduce_backlog with the positive backlog and causes an
underflow in the tbf parent's backlog (4096 Mb instead of 0).
To fix this issue, the codepath for all clients of qdisc_dequeue_internal
has been simplified: codel, pie, hhf, fq, fq_pie, and fq_codel.
qdisc_dequeue_internal handles the backlog adjustments for all cases that
do not directly use the dequeue handler.
The old fq_codel_change limit adjustment loop accumulated the arguments to
the subsequent qdisc_tree_reduce_backlog call through the cstats field.
However, this is confusing and error prone as fq_codel_dequeue could also
potentially mutate this field (which qdisc_dequeue_internal calls in the
non gso_skb case), so we have unified the code here with other qdiscs. |
| In the Linux kernel, the following vulnerability has been resolved:
habanalabs: fix UAF in export_dmabuf()
As soon as we'd inserted a file reference into descriptor table, another
thread could close it. That's fine for the case when all we are doing is
returning that descriptor to userland (it's a race, but it's a userland
race and there's nothing the kernel can do about it). However, if we
follow fd_install() with any kind of access to objects that would be
destroyed on close (be it the struct file itself or anything destroyed
by its ->release()), we have a UAF.
dma_buf_fd() is a combination of reserving a descriptor and fd_install().
habanalabs export_dmabuf() calls it and then proceeds to access the
objects destroyed on close. In particular, it grabs an extra reference to
another struct file that will be dropped as part of ->release() for ours;
that "will be" is actually "might have already been".
Fix that by reserving descriptor before anything else and do fd_install()
only when everything had been set up. As a side benefit, we no longer
have the failure exit with file already created, but reference to
underlying file (as well as ->dmabuf_export_cnt, etc.) not grabbed yet;
unlike dma_buf_fd(), fd_install() can't fail. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: cancle set bad inode after removing name fails
The reproducer uses a file0 on a ntfs3 file system with a corrupted i_link.
When renaming, the file0's inode is marked as a bad inode because the file
name cannot be deleted.
The underlying bug is that make_bad_inode() is called on a live inode.
In some cases it's "icache lookup finds a normal inode, d_splice_alias()
is called to attach it to dentry, while another thread decides to call
make_bad_inode() on it - that would evict it from icache, but we'd already
found it there earlier".
In some it's outright "we have an inode attached to dentry - that's how we
got it in the first place; let's call make_bad_inode() on it just for shits
and giggles". |
| In the Linux kernel, the following vulnerability has been resolved:
xen: fix UAF in dmabuf_exp_from_pages()
[dma_buf_fd() fixes; no preferences regarding the tree it goes through -
up to xen folks]
As soon as we'd inserted a file reference into descriptor table, another
thread could close it. That's fine for the case when all we are doing is
returning that descriptor to userland (it's a race, but it's a userland
race and there's nothing the kernel can do about it). However, if we
follow fd_install() with any kind of access to objects that would be
destroyed on close (be it the struct file itself or anything destroyed
by its ->release()), we have a UAF.
dma_buf_fd() is a combination of reserving a descriptor and fd_install().
gntdev dmabuf_exp_from_pages() calls it and then proceeds to access the
objects destroyed on close - starting with gntdev_dmabuf itself.
Fix that by doing reserving descriptor before anything else and do
fd_install() only when everything had been set up. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Remove skb secpath if xfrm state is not found
Hardware returns a unique identifier for a decrypted packet's xfrm
state, this state is looked up in an xarray. However, the state might
have been freed by the time of this lookup.
Currently, if the state is not found, only a counter is incremented.
The secpath (sp) extension on the skb is not removed, resulting in
sp->len becoming 0.
Subsequently, functions like __xfrm_policy_check() attempt to access
fields such as xfrm_input_state(skb)->xso.type (which dereferences
sp->xvec[sp->len - 1]) without first validating sp->len. This leads to
a crash when dereferencing an invalid state pointer.
This patch prevents the crash by explicitly removing the secpath
extension from the skb if the xfrm state is not found after hardware
decryption. This ensures downstream functions do not operate on a
zero-length secpath.
BUG: unable to handle page fault for address: ffffffff000002c8
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 282e067 P4D 282e067 PUD 0
Oops: Oops: 0000 [#1] SMP
CPU: 12 UID: 0 PID: 0 Comm: swapper/12 Not tainted 6.15.0-rc7_for_upstream_min_debug_2025_05_27_22_44 #1 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:__xfrm_policy_check+0x61a/0xa30
Code: b6 77 7f 83 e6 02 74 14 4d 8b af d8 00 00 00 41 0f b6 45 05 c1 e0 03 48 98 49 01 c5 41 8b 45 00 83 e8 01 48 98 49 8b 44 c5 10 <0f> b6 80 c8 02 00 00 83 e0 0c 3c 04 0f 84 0c 02 00 00 31 ff 80 fa
RSP: 0018:ffff88885fb04918 EFLAGS: 00010297
RAX: ffffffff00000000 RBX: 0000000000000002 RCX: 0000000000000000
RDX: 0000000000000002 RSI: 0000000000000002 RDI: 0000000000000000
RBP: ffffffff8311af80 R08: 0000000000000020 R09: 00000000c2eda353
R10: ffff88812be2bbc8 R11: 000000001faab533 R12: ffff88885fb049c8
R13: ffff88812be2bbc8 R14: 0000000000000000 R15: ffff88811896ae00
FS: 0000000000000000(0000) GS:ffff8888dca82000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffff000002c8 CR3: 0000000243050002 CR4: 0000000000372eb0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
? try_to_wake_up+0x108/0x4c0
? udp4_lib_lookup2+0xbe/0x150
? udp_lib_lport_inuse+0x100/0x100
? __udp4_lib_lookup+0x2b0/0x410
__xfrm_policy_check2.constprop.0+0x11e/0x130
udp_queue_rcv_one_skb+0x1d/0x530
udp_unicast_rcv_skb+0x76/0x90
__udp4_lib_rcv+0xa64/0xe90
ip_protocol_deliver_rcu+0x20/0x130
ip_local_deliver_finish+0x75/0xa0
ip_local_deliver+0xc1/0xd0
? ip_protocol_deliver_rcu+0x130/0x130
ip_sublist_rcv+0x1f9/0x240
? ip_rcv_finish_core+0x430/0x430
ip_list_rcv+0xfc/0x130
__netif_receive_skb_list_core+0x181/0x1e0
netif_receive_skb_list_internal+0x200/0x360
? mlx5e_build_rx_skb+0x1bc/0xda0 [mlx5_core]
gro_receive_skb+0xfd/0x210
mlx5e_handle_rx_cqe_mpwrq+0x141/0x280 [mlx5_core]
mlx5e_poll_rx_cq+0xcc/0x8e0 [mlx5_core]
? mlx5e_handle_rx_dim+0x91/0xd0 [mlx5_core]
mlx5e_napi_poll+0x114/0xab0 [mlx5_core]
__napi_poll+0x25/0x170
net_rx_action+0x32d/0x3a0
? mlx5_eq_comp_int+0x8d/0x280 [mlx5_core]
? notifier_call_chain+0x33/0xa0
handle_softirqs+0xda/0x250
irq_exit_rcu+0x6d/0xc0
common_interrupt+0x81/0xa0
</IRQ> |
